International Journal of Transportation Engineering and Technology

Volume 2, Issue 4, December 2016

  • Design of a Small UAV Combined Between Flying-Wing and Quadrotor with XFRL5

    Ngo Khanh Hieu, Pham Quang Vinh, Dinh Anh Bao

    Issue: Volume 2, Issue 4-1, December 2016
    Pages: 1-6
    Received: 13 April 2016
    Accepted: 22 July 2016
    Published: 3 September 2016
    DOI: 10.11648/j.ijtet.s.2016020501.11
    Downloads:
    Views:
    This article belongs to the Special Issue Experiments Researches in Aeronautical Engineering
    Abstract: The design process of a product is a multi-step process of selection and assessment criteria to create a final product which meets all the needs of the practice. A small UAV combined between flying-wing and quadrotor is a very complex product, so the design process of this small UAV requires a thorough and circumspect review. The problem is how to ... Show More
  • Methods of Manufacturing Aeroelasticity Bench Test for NACA0012 Wing Model in the Low Speed Wind Tunnel

    Thi Tuyet Nhung Le, Thanh Phat Duong, Nhat Truong Hoang

    Issue: Volume 2, Issue 4-1, December 2016
    Pages: 7-11
    Received: 16 August 2016
    Accepted: 22 August 2016
    Published: 19 September 2016
    DOI: 10.11648/j.ijtet.s.2016020501.12
    Downloads:
    Views:
    This article belongs to the Special Issue Experiments Researches in Aeronautical Engineering
    Abstract: The purpose of this study is to take measures to manufacture the experimental model: NACA 0012 wing model in the low speed wind tunnel (38 m/s). The parameters base on the achieved results of Thi-Tuyet Nhung Le & al.: “Design of aeroelasticity bench test for NACA0012 wing model in the low speed wind tunnel: Influence of wing’s parameters on flutter... Show More
  • The Geometric Influence of the Tubular-Hat Tube on Its Energy Absorption Capacity in Axial Load

    Hung Anh Ly, Thanh Tien Pham

    Issue: Volume 2, Issue 4-1, December 2016
    Pages: 12-17
    Received: 12 August 2016
    Accepted: 9 October 2016
    Published: 22 November 2016
    DOI: 10.11648/j.ijtet.s.2016020501.13
    Downloads:
    Views:
    This article belongs to the Special Issue Experiments Researches in Aeronautical Engineering
    Abstract: Crashworthiness is an important criterion in vehicle design. In fact, a crashworthy design will reduce the terrible accidents that happen everyday. Normally, tube structures are used for this task by dissipating the impact energy on the folding waves formed during the crushing progress. This study continues the previous studies, focuses on analyzin... Show More
  • Behavior of Tubular Hat Structure Under Three Point Bending

    Le Duy Hien, Ly Hung Anh

    Issue: Volume 2, Issue 4-1, December 2016
    Pages: 18-24
    Received: 12 August 2016
    Accepted: 9 October 2016
    Published: 22 November 2016
    DOI: 10.11648/j.ijtet.s.2016020501.14
    Downloads:
    Views:
    This article belongs to the Special Issue Experiments Researches in Aeronautical Engineering
    Abstract: The paper focuses on the energy absorption capacity of structural materials, the most important in frame design, the structure of the vehicles, scaffolding. Main content include new solution with comparing the general structure cylinder, square tube, top-hat and reverse top-hat. After that, considering and comparing displacement, force in the trans... Show More